Exam Details
| Subject | mechanical drafting | |
| Paper | ||
| Exam / Course | diploma engineering | |
| Department | ||
| Organization | Gujarat Technological University | |
| Position | ||
| Exam Date | January, 2019 | |
| City, State | gujarat, ahmedabad |
Question Paper
1/9
Seat No.: Enrolment
GUJARAT TECHNOLOGICAL UNIVERSITY
DIPLOMA ENGINEERING- C to D Bridge Course Examination WINTER 2018
Subject Code: C321901 Date: 07-01-2019
Subject Name: Mechanical Drafting
Time: 10:30 AM TO 12:00 PM Total Marks: 70
Instructions:
1. Attempt all questions.
2. Make suitable assumptions wherever necessary.
3. Each question is of 1 mark.
4. Use of only simple calculator is permitted. (Scientific/Higher Version not allowed).
5. English version is authentic
No.
Question Text and Option.
1.
Grade pencil is known as soft grade pencil.
A.
2B
B.
2H
C.
6H
D.
F
A.
2
B.
2
C.
6
D.
2.
Dimension line should not each other.
A.
Parallel
B.
Cross
C.
Perpendicular
D.
Inclined
A.
B.
C.
D.
3.
When all the dimension are placed above the dimension line, it is
A.
Aligned system
B.
Unidirectional system
C.
Both A B
D.
None of this.
A.
B.
C.
D.
4.
are used for drawing curves which cannot be drawn by compass.
A.
Divider
B.
Stock
C.
Protector
D.
French curve
A.
B.
C.
D.
5.
The T-square is used to draw lines.
A.
Horizontal line
B.
Radial line
C.
Triangulation line
D.
Vertical line
A.
B.
C.
D.
6.
The A2 size of drawing sheet has the following size:
A.
841mm X 1189mm
B.
420mm X 594mm
C.
297mm X 420mm
D.
210mm X 297mm
A2
A.
X
B.
X
C.
X
D.
X
2/9
7.
Hidden lines are drawn as
A.
Dashed narrow line
B.
Dashed wide line
C.
Long -dashed dotted wide line
D.
Long-dashed double dotted wide line.
A.
B.
C.
D.
8.
The dimension figure for radius of a circle should be preceded by
A.
R
B.
CR
C.
SR
D.
RAD
A.
R
B.
CR
C.
SR
D.
RAD
9.
Center lines are used to locate or represent the centers
A.
Arcs
B.
Circles
C.
Hidden round features
D.
All of this
A.
B.
C.
D.
10.
A full scale technical drawing has a scale factor
A.
1:1
B.
1:2
C.
2:1
D.
1:4
A.
B.
C.
D.
11.
The arrowhead is having the
A.
Half the width
B.
Equal the width
C.
Two times the width
D.
Three times the width
A.
B.
C.
D.
12.
The included angle of a hexagon is
A.
B.
C.
120˚c
D.
150˚c
A.
B.
C.
120˚c
D.
150˚c
13.
The primary unit of measurement for engineering drawing and design in the mechanical industries is the
A.
millimetre
B.
Centimetre
C.
meter
D.
Kilometre
A.
B.
C.
D.
14.
The top and right side views have common dimension of
A.
Height and width
B.
Width and depth
C.
Height
D.
Depth
A.
B.
C.
D.
15.
The top view of an object should typically be drawn
A.
To the right of front view
B.
Directly below the front view
C.
Anywhere on the same page
D.
On a separate piece of paper
3/9
A.
B.
C.
D.
16.
If right hand side view of an object is drawn on left side then the method is known as_
A.
1st angle
B.
2nd angle
C.
3rd angle
D.
4th angle
A.
B.
C.
D.
17.
view, top view and bottom view have equal horizontal length.
A.
Front
B.
Right side
C.
Both A B
D.
None of this
A.
B.
C.
A B
D.
18.
The most common projection used in machine drawing
A.
Isometric
B.
Diametric
C.
Orthographic
D.
Perspective
A.
B.
C.
D.
19.
For drawn of top view following is not used.
A.
Height
B.
Width
C.
Length
D.
None of this
A.
B.
C.
D.
20.
When any object edge is not appears in front side, has its projection of edge is drawn line
A.
Full
B.
Dotted
C.
Wavy
D.
Thick
A.
B.
C.
D.
21.
are not sectioned.
A.
Shafts
B.
Keys and bolts
C.
All of this
D.
None of this
A.
B.
C.
D.
22.
The angle of hatching line is
A.
30
B.
60
C.
75
D.
45
A.
B.
C.
D.
23.
The hatching between two meshing surfaces
A.
In the same direction
B.
In the opposite direction
C.
None of these
D.
All of these
...........................
A.
B.
C.
D.
24.
has one base.
4/9
A.
Cylinder
B.
Prism
C.
Pyramid
D.
All of this
A.
B.
C.
D.
25.
A solid having minimum number of faces is
A.
Tetrahedron
B.
Triangular prism
C.
Square pyramid
D.
Cube
A.
B.
C.
D.
26.
A pyramid is cut by a plane parallel to its base removing the apex, the remaining part is known as
A.
Truncated
B.
Frustum
C.
Sectioned
D.
Prism
A.
B.
C.
D.
27.
Number of faces in a dodecahedron are
A.
4
B.
8
C.
12
D.
20
A.
B.
C.
D.
28.
An orthographic view of a hemisphere may appear as
A.
Circle
B.
Ellipse
C.
Parabola
D.
Hyperbola
A.
B.
C.
D.
29.
The imaginary line joining the center of two base of the prism is
A.
Edge
B.
Axis
C.
Apex
D.
Generator
A.
B.
C.
D.
30.
has as many numbers of triangular faces as number of base sides.
A.
Pyramid
B.
Prism
C.
Cylinder
D.
All of these
A.
B.
C.
D.
31.
Surface development of a cylinder is
A.
Triangle
B.
Rectangle
C.
Circle
D.
None of these
A.
B.
C.
D.
32.
The recommend symbol for indicating the first angle of projection shows two views of frustum of a
A.
Square pyramid
B.
Triangular pyramid
5/9
C.
cone
D.
None of these
A.
B.
C.
D.
33.
having faces of both top and bottom end are same.
A.
Prism
B.
Pyramid
C.
cone
D.
Truncated
A.
B.
C.
D.
34.
The study of intersection of surfaces helps in
A.
Sheet metal work
B.
Building drawing
C.
Architectural drawing
D.
All of these
A.
B.
C.
D.
35.
In any view, liquid is drawn by
A.
Full line
B.
Dotted line
C.
Wavy line
D.
Thick line
A.
B.
C.
D.
36.
The circumference of a circle is equal
A.
B.
2πr2
C.
2πr
D.
r2
A.
B.
2πr2
C.
2πr
D.
r2
37.
Surface roughness symbol is
A.
Rectangle
B.
Triangle
C.
Circle
D.
None of these
A.
B.
C.
D.
38.
Surface development of pyramid is drawn by length as a radius.
A.
Slant edge
B.
Axis
C.
Base edge
D.
Vertical edge
A.
B.
C.
D.
39.
Surface roughness is indicating in
A.
Meter
B.
Milimetre
C.
Centimetre
D.
Micron
A.
B.
C.
D.
40.
Development of sphere is done by
A.
Zone or Lune method
B.
Parallel line or Radial line method
C.
Triangulation method
D.
None of these
A.
B.
C.
D.
6/9
41.
The solid having a square for a base and triangular lateral faces intersecting at a vertex is
A.
Prism
B.
Pyramid
C.
Cone
D.
Torus
A.
B.
C.
D.
42.
Intersection of is a straight line.
A.
Prism ,Pyramid
B.
Pyramid, Cylinder
C.
Prism ,Cylinder
D.
Cylinder, Cylinder
A.
B.
C.
D.
43.
Intersection of is a curve line.
A.
Pyramid, Prism
B.
Two Prism
C.
Cylinder, Cone
D.
Two Pryamid
A.
B.
C.
D.
44.
The intersection of cone by a plane results in
A.
Conic section
B.
Cycloid
C.
helix
D.
None of these
A.
B.
C.
D.
45.
A cone resting on its base on the HP is cut by a section plane parallel to VP has its sectional front view
A.
Ellipse
B.
Parabola
C.
Hyperbola
D.
Semicircle
HP
A.
B.
C.
D.
46.
When a view is projected on a surface to the cutting plane it is called true shape of section
A.
Perpendicular
B.
Parallel
C.
Inclined
D.
None of these
A.
B.
C.
D.
47.
Funnel is made by joining
A.
Pyramid
B.
Cylinder
C.
Prism
D.
Cone
A.
B.
C.
D.
48.
The sectional view gives of object.
A.
Dimension
B.
Internal detail
C.
None of A B
D.
Both A B
A.
B.
7/9
C.
D.
49.
The included angle in ACME threads
A.
B.
C.
D.
47.5˚
ACME
A.
B.
C.
D.
50.
of the following is used as permanent fastening.
A.
Bolts
B.
Keys
C.
Rivet
D.
Cotter
A.
B.
C.
D.
51.
A rivet is specified by
A.
Shank diameter
B.
Length of rivet
C.
Type of head
D.
Length of tail
A.
B.
C.
D.
52.
The part list should include the
A.
Part number
B.
Number of parts needed
C.
Manufacturing material
D.
All of these
A.
B.
C.
D.
53.
The joint which permit angular movement
A.
Sleeve joint
B.
Strap joint
C.
Knuckle joint
D.
Cotter joint
A.
B.
C.
D.
54.
Fork End is a part
A.
Sleeve joint
B.
Strap joint
C.
Knuckle joint
D.
Cotter joint
A.
B.
C.
D.
55.
These include taper pins, straight pin, dowel pins, clevis pin and cotter pins.
A.
Bolts
B.
General fasteners
C.
Machine pin
D.
Rivets
A.
B.
C.
D.
56.
is a part of knuckle joint.
A.
Cotter
B.
Spigot
C.
Socket
D.
Pin
A.
B.
C.
D.
57.
Sewage pipes are generally made of
A.
Mild steel
B.
Aluminium
C.
Cast iron
D.
Reinforced concrete cement
8/9
A.
B.
C.
D.
58.
is used to increase length of pipe.
A.
Nipple
B.
Elbow
C.
Cap
D.
Plug
A.
B.
C.
D.
59.
is a symbol of gas pipe line.
A.
B.
C.
D.
A.
B.
C.
D.
60.
is a part of screw jack.
A.
Cup
B.
Bush
C.
Socket
D.
Block
A.
B.
C.
D.
61.
This is the smallest diameter of a screw thread:
A.
Internal thread diameter
B.
Minor diameter
C.
Major diameter
D.
External thread diameter
A.
B.
C.
D.
62.
For application involving high stresses in one direction only the following type of thread would be best suited
A.
Square thread
B.
ACME thread
C.
Buttress thread
D.
Isometric thread
A.
B.
ACME
C.
D.
63.
is used for stop inside threaded fitting of joint.
A.
Coupling
B.
Elbow
C.
Reducer
D.
Plug
A.
B.
C.
D.
64.
is used for bending a pipe line at 90 degree.
A.
Coupling
B.
Elbow
C.
Reducer
D.
Plug
A.
B.
C.
D.
65.
is used for joining two same hole pipe in straight line.
A.
Coupling
B.
Elbow
C.
Reducer
D.
Plug
A.
B.
C.
D.
9/9
66.
The flanged pipe joint is used for
A.
Low fluid pressure
B.
High temperature fluid
C.
Medium fluid pressure
D.
High fluid pressure
A.
B.
C.
D.
67.
is symbol
A.
Square butt weld
B.
Double butt weld
C.
Parallel butt weld
D.
None of this
એ.................
A.
B.
C.
D.
68.
is a part of foot step bearing.
A.
Fork end
B.
Pin
C.
Collar
D.
Bush
A.
B.
C.
D.
69.
Spigot is a part of
A.
Knuckle joint
B.
Cotter joint
C.
Sleeve joint
D.
Strap joint
A.
B.
C.
D.
70.
In a screw thread nominal diameter is equal
A.
Root diameter
B.
Effective diameter
C.
Major diameter
D.
None of this.
A.
B.
C.
D.
Seat No.: Enrolment
GUJARAT TECHNOLOGICAL UNIVERSITY
DIPLOMA ENGINEERING- C to D Bridge Course Examination WINTER 2018
Subject Code: C321901 Date: 07-01-2019
Subject Name: Mechanical Drafting
Time: 10:30 AM TO 12:00 PM Total Marks: 70
Instructions:
1. Attempt all questions.
2. Make suitable assumptions wherever necessary.
3. Each question is of 1 mark.
4. Use of only simple calculator is permitted. (Scientific/Higher Version not allowed).
5. English version is authentic
No.
Question Text and Option.
1.
Grade pencil is known as soft grade pencil.
A.
2B
B.
2H
C.
6H
D.
F
A.
2
B.
2
C.
6
D.
2.
Dimension line should not each other.
A.
Parallel
B.
Cross
C.
Perpendicular
D.
Inclined
A.
B.
C.
D.
3.
When all the dimension are placed above the dimension line, it is
A.
Aligned system
B.
Unidirectional system
C.
Both A B
D.
None of this.
A.
B.
C.
D.
4.
are used for drawing curves which cannot be drawn by compass.
A.
Divider
B.
Stock
C.
Protector
D.
French curve
A.
B.
C.
D.
5.
The T-square is used to draw lines.
A.
Horizontal line
B.
Radial line
C.
Triangulation line
D.
Vertical line
A.
B.
C.
D.
6.
The A2 size of drawing sheet has the following size:
A.
841mm X 1189mm
B.
420mm X 594mm
C.
297mm X 420mm
D.
210mm X 297mm
A2
A.
X
B.
X
C.
X
D.
X
2/9
7.
Hidden lines are drawn as
A.
Dashed narrow line
B.
Dashed wide line
C.
Long -dashed dotted wide line
D.
Long-dashed double dotted wide line.
A.
B.
C.
D.
8.
The dimension figure for radius of a circle should be preceded by
A.
R
B.
CR
C.
SR
D.
RAD
A.
R
B.
CR
C.
SR
D.
RAD
9.
Center lines are used to locate or represent the centers
A.
Arcs
B.
Circles
C.
Hidden round features
D.
All of this
A.
B.
C.
D.
10.
A full scale technical drawing has a scale factor
A.
1:1
B.
1:2
C.
2:1
D.
1:4
A.
B.
C.
D.
11.
The arrowhead is having the
A.
Half the width
B.
Equal the width
C.
Two times the width
D.
Three times the width
A.
B.
C.
D.
12.
The included angle of a hexagon is
A.
B.
C.
120˚c
D.
150˚c
A.
B.
C.
120˚c
D.
150˚c
13.
The primary unit of measurement for engineering drawing and design in the mechanical industries is the
A.
millimetre
B.
Centimetre
C.
meter
D.
Kilometre
A.
B.
C.
D.
14.
The top and right side views have common dimension of
A.
Height and width
B.
Width and depth
C.
Height
D.
Depth
A.
B.
C.
D.
15.
The top view of an object should typically be drawn
A.
To the right of front view
B.
Directly below the front view
C.
Anywhere on the same page
D.
On a separate piece of paper
3/9
A.
B.
C.
D.
16.
If right hand side view of an object is drawn on left side then the method is known as_
A.
1st angle
B.
2nd angle
C.
3rd angle
D.
4th angle
A.
B.
C.
D.
17.
view, top view and bottom view have equal horizontal length.
A.
Front
B.
Right side
C.
Both A B
D.
None of this
A.
B.
C.
A B
D.
18.
The most common projection used in machine drawing
A.
Isometric
B.
Diametric
C.
Orthographic
D.
Perspective
A.
B.
C.
D.
19.
For drawn of top view following is not used.
A.
Height
B.
Width
C.
Length
D.
None of this
A.
B.
C.
D.
20.
When any object edge is not appears in front side, has its projection of edge is drawn line
A.
Full
B.
Dotted
C.
Wavy
D.
Thick
A.
B.
C.
D.
21.
are not sectioned.
A.
Shafts
B.
Keys and bolts
C.
All of this
D.
None of this
A.
B.
C.
D.
22.
The angle of hatching line is
A.
30
B.
60
C.
75
D.
45
A.
B.
C.
D.
23.
The hatching between two meshing surfaces
A.
In the same direction
B.
In the opposite direction
C.
None of these
D.
All of these
...........................
A.
B.
C.
D.
24.
has one base.
4/9
A.
Cylinder
B.
Prism
C.
Pyramid
D.
All of this
A.
B.
C.
D.
25.
A solid having minimum number of faces is
A.
Tetrahedron
B.
Triangular prism
C.
Square pyramid
D.
Cube
A.
B.
C.
D.
26.
A pyramid is cut by a plane parallel to its base removing the apex, the remaining part is known as
A.
Truncated
B.
Frustum
C.
Sectioned
D.
Prism
A.
B.
C.
D.
27.
Number of faces in a dodecahedron are
A.
4
B.
8
C.
12
D.
20
A.
B.
C.
D.
28.
An orthographic view of a hemisphere may appear as
A.
Circle
B.
Ellipse
C.
Parabola
D.
Hyperbola
A.
B.
C.
D.
29.
The imaginary line joining the center of two base of the prism is
A.
Edge
B.
Axis
C.
Apex
D.
Generator
A.
B.
C.
D.
30.
has as many numbers of triangular faces as number of base sides.
A.
Pyramid
B.
Prism
C.
Cylinder
D.
All of these
A.
B.
C.
D.
31.
Surface development of a cylinder is
A.
Triangle
B.
Rectangle
C.
Circle
D.
None of these
A.
B.
C.
D.
32.
The recommend symbol for indicating the first angle of projection shows two views of frustum of a
A.
Square pyramid
B.
Triangular pyramid
5/9
C.
cone
D.
None of these
A.
B.
C.
D.
33.
having faces of both top and bottom end are same.
A.
Prism
B.
Pyramid
C.
cone
D.
Truncated
A.
B.
C.
D.
34.
The study of intersection of surfaces helps in
A.
Sheet metal work
B.
Building drawing
C.
Architectural drawing
D.
All of these
A.
B.
C.
D.
35.
In any view, liquid is drawn by
A.
Full line
B.
Dotted line
C.
Wavy line
D.
Thick line
A.
B.
C.
D.
36.
The circumference of a circle is equal
A.
B.
2πr2
C.
2πr
D.
r2
A.
B.
2πr2
C.
2πr
D.
r2
37.
Surface roughness symbol is
A.
Rectangle
B.
Triangle
C.
Circle
D.
None of these
A.
B.
C.
D.
38.
Surface development of pyramid is drawn by length as a radius.
A.
Slant edge
B.
Axis
C.
Base edge
D.
Vertical edge
A.
B.
C.
D.
39.
Surface roughness is indicating in
A.
Meter
B.
Milimetre
C.
Centimetre
D.
Micron
A.
B.
C.
D.
40.
Development of sphere is done by
A.
Zone or Lune method
B.
Parallel line or Radial line method
C.
Triangulation method
D.
None of these
A.
B.
C.
D.
6/9
41.
The solid having a square for a base and triangular lateral faces intersecting at a vertex is
A.
Prism
B.
Pyramid
C.
Cone
D.
Torus
A.
B.
C.
D.
42.
Intersection of is a straight line.
A.
Prism ,Pyramid
B.
Pyramid, Cylinder
C.
Prism ,Cylinder
D.
Cylinder, Cylinder
A.
B.
C.
D.
43.
Intersection of is a curve line.
A.
Pyramid, Prism
B.
Two Prism
C.
Cylinder, Cone
D.
Two Pryamid
A.
B.
C.
D.
44.
The intersection of cone by a plane results in
A.
Conic section
B.
Cycloid
C.
helix
D.
None of these
A.
B.
C.
D.
45.
A cone resting on its base on the HP is cut by a section plane parallel to VP has its sectional front view
A.
Ellipse
B.
Parabola
C.
Hyperbola
D.
Semicircle
HP
A.
B.
C.
D.
46.
When a view is projected on a surface to the cutting plane it is called true shape of section
A.
Perpendicular
B.
Parallel
C.
Inclined
D.
None of these
A.
B.
C.
D.
47.
Funnel is made by joining
A.
Pyramid
B.
Cylinder
C.
Prism
D.
Cone
A.
B.
C.
D.
48.
The sectional view gives of object.
A.
Dimension
B.
Internal detail
C.
None of A B
D.
Both A B
A.
B.
7/9
C.
D.
49.
The included angle in ACME threads
A.
B.
C.
D.
47.5˚
ACME
A.
B.
C.
D.
50.
of the following is used as permanent fastening.
A.
Bolts
B.
Keys
C.
Rivet
D.
Cotter
A.
B.
C.
D.
51.
A rivet is specified by
A.
Shank diameter
B.
Length of rivet
C.
Type of head
D.
Length of tail
A.
B.
C.
D.
52.
The part list should include the
A.
Part number
B.
Number of parts needed
C.
Manufacturing material
D.
All of these
A.
B.
C.
D.
53.
The joint which permit angular movement
A.
Sleeve joint
B.
Strap joint
C.
Knuckle joint
D.
Cotter joint
A.
B.
C.
D.
54.
Fork End is a part
A.
Sleeve joint
B.
Strap joint
C.
Knuckle joint
D.
Cotter joint
A.
B.
C.
D.
55.
These include taper pins, straight pin, dowel pins, clevis pin and cotter pins.
A.
Bolts
B.
General fasteners
C.
Machine pin
D.
Rivets
A.
B.
C.
D.
56.
is a part of knuckle joint.
A.
Cotter
B.
Spigot
C.
Socket
D.
Pin
A.
B.
C.
D.
57.
Sewage pipes are generally made of
A.
Mild steel
B.
Aluminium
C.
Cast iron
D.
Reinforced concrete cement
8/9
A.
B.
C.
D.
58.
is used to increase length of pipe.
A.
Nipple
B.
Elbow
C.
Cap
D.
Plug
A.
B.
C.
D.
59.
is a symbol of gas pipe line.
A.
B.
C.
D.
A.
B.
C.
D.
60.
is a part of screw jack.
A.
Cup
B.
Bush
C.
Socket
D.
Block
A.
B.
C.
D.
61.
This is the smallest diameter of a screw thread:
A.
Internal thread diameter
B.
Minor diameter
C.
Major diameter
D.
External thread diameter
A.
B.
C.
D.
62.
For application involving high stresses in one direction only the following type of thread would be best suited
A.
Square thread
B.
ACME thread
C.
Buttress thread
D.
Isometric thread
A.
B.
ACME
C.
D.
63.
is used for stop inside threaded fitting of joint.
A.
Coupling
B.
Elbow
C.
Reducer
D.
Plug
A.
B.
C.
D.
64.
is used for bending a pipe line at 90 degree.
A.
Coupling
B.
Elbow
C.
Reducer
D.
Plug
A.
B.
C.
D.
65.
is used for joining two same hole pipe in straight line.
A.
Coupling
B.
Elbow
C.
Reducer
D.
Plug
A.
B.
C.
D.
9/9
66.
The flanged pipe joint is used for
A.
Low fluid pressure
B.
High temperature fluid
C.
Medium fluid pressure
D.
High fluid pressure
A.
B.
C.
D.
67.
is symbol
A.
Square butt weld
B.
Double butt weld
C.
Parallel butt weld
D.
None of this
એ.................
A.
B.
C.
D.
68.
is a part of foot step bearing.
A.
Fork end
B.
Pin
C.
Collar
D.
Bush
A.
B.
C.
D.
69.
Spigot is a part of
A.
Knuckle joint
B.
Cotter joint
C.
Sleeve joint
D.
Strap joint
A.
B.
C.
D.
70.
In a screw thread nominal diameter is equal
A.
Root diameter
B.
Effective diameter
C.
Major diameter
D.
None of this.
A.
B.
C.
D.
Other Question Papers
Subjects
- a. c. distribution & utilization
- a.c. distribution & utilization
- advance manufacturing system
- advanced building materials
- advanced computer programming
- advanced mathematics (group-1)
- advanced mathematics(group-2)
- aircraft maintenance-ii
- aircraft navigation and radio system
- aircraft performance & stability
- applied electronics and instrumentation
- applied science-i (physics)
- applied science-ii(chemistry)
- architectural drawing-ii
- automation in fabrication technology
- automobile electrical system
- automobile engines
- automobile transmission & mechanism
- basic automobile design
- basic avionics
- basic chemistry ( group-4)
- basic control system
- basic design
- basic electronic circuits
- basic electronics
- basic of electrical and electronics engineering
- basic of electrical engineering
- building material
- chemical engineering plant economics
- chemical process equipment design
- chemical process technology - i
- chemical process technology - ii
- chemical process technology –i
- civil engineering drawing
- cnc machines
- communication engineering- i
- communication engineering-ii
- communication skill
- communication skill-ii (aa)
- communication skills
- computer aided modelling & design
- computer application in wet processing
- computer graphics
- computer maintenance
- computer organization and architecture
- construction technology
- construction works management
- control system components
- costing estimation & management
- d.c.circuits
- data & computer communication
- data structure management
- database management system
- database programming with vb.net
- design fundamental-i
- design fundamental-ii
- design visualization
- digital electronics
- drying and firing
- dyes and pharmaceuticals
- ecology & environmental pollution
- electical machine-1
- electrical installation & maintenance
- electrical instrumentation
- electrical machine-ii
- electronic materials & components
- electronic materials and component
- electronic networks
- electronics devices and circuits-i
- electronics devices and circuits-ii
- electronics instrument & measurements
- electronics networks & lines
- elements of civil engineering
- elements of mechanical engineering
- engineering drawing
- engineering mechanics
- english communication and architecture vocabulary
- entrepreneurship development
- environmental monitoring
- essentials of environment & seismic engineering
- estimating & costing
- estimating and costing - i
- extrusion die design
- fabric structure - ii
- fabrication technology
- fabrication technology - ii
- fiber optic communication
- finishing technology for textile
- fluid flow operation
- fluid mechanics & hydraulic machines
- fundamental of chemical engineering reactions & thermo dynamics
- fundamental of electronics circuits
- fundamental of mechanical engineering
- generation and transmission of electrical power
- glass-ii
- high performance & green plastics
- history of architecture - ii
- history of architecture -i
- history of architecture(indian)
- human resource management
- hydraulic and pneumatic
- hydraulic and pneumatic devices
- hydraulics
- industrial management
- industrial stoichiometry
- irrigation engineering
- manufacturing engineering-1
- manufacturing engineering-i
- manufacturing engineering-ii
- manufacturing process & material technology
- mass transfer - i
- mass transfer-i
- material science and metallurgy
- material technology
- mathematics - i
- mechanical drafting
- mechanical operation (ceo- i)
- mechanical operation (ceo-i)
- mechanics of structure-ii
- mechanics of structures - i
- metrology & instrumentation
- microcontroller
- microprocessor & assembly language programming
- mine surveying-ii
- non conventional energy sources
- operating system
- organic chemistry
- petroleum refining & petro chemical technology
- physical analytical & inorganic chemistry
- plant maintenance & safety
- polymer chemistry - 1
- polymer chemistry - ii
- principles of chemical engineering
- process equipment design
- process heat transfer
- process technology
- processing of thermoset
- programmable logic controller
- programming in c
- programming in c++
- pulp and paper technology
- quantity survey & costing
- refractory
- relational database management system
- robotics & automated material handling
- ship building & ship recycling
- software engineering
- soil engineering
- strength of materials
- structure - i
- structure-i
- surveying
- surveying - i
- surveying-ii
- system analysis design
- technical drawing- i
- technology of technical textiles
- television engineering
- theory of machine
- thermodynamics
- thermodynamics & hydraulics
- transportation engineering
- under ground mining of coal
- utilities and instrumentation in chemical plant
- vehicle dynamics
- visual basic
- water resources management
- white ware
- yarn manufacturing technology-iii