Exam Details
Subject | Optical Counter Management | |
Paper | ||
Exam / Course | Certificate In Dispensing Optics (CDO) | |
Department | School of Health Science (SOHS) | |
Organization | indira gandhi national open university | |
Position | ||
Exam Date | December, 2015 | |
City, State | new delhi, |
Question Paper
1. A general rule for standard alignment is to begin with
Bridge
Temple
Nosepads
None of the above
2. Zyl frames must be
Heated
Melted
Freezed
None of the above
3. The frame front is somewhat twisted so that the planes of the two lenses are out of coincidence with each other, known as
Two Point Touch
Four Point Touch
X-ing
None of the above
4. Which of the following is finer than the Zyl file, and this file is often used to file metal parts of a frame?
Zyl file
Slotting file
Pillar file
Rat-tail file
5. Splay angle should be in the range of
20° to 30°
15° to 30°
25° to 30°
20° to 23°
6. For frontal angle, the tops of the pads should be closer together than the bottoms, angling in towards each other approximately
10°
20°
30°
40°
7. Frames with a heavy front and light sides will tend to slip
Forwards
Backwards
Downwards
Upwards
8. What do patients/customers want?
Reliability and Responsiveness
Assurance and Empathy
Tangibles
All of the above
9. Which parameter to bend of hockey end sides can be adjusted within a few millimetres and in fact, is best done with the patient's presence?
Height
Length
Width
Depth
10. Which of the following progressive lens designs will provide wider fields of clear vision, at the expense of higher levels of swim, distortion and blur?
Harder
Softer
Both and
None of the above
11. The most convenient method of dispensing and adjusting the finished glasses is for the practitioner to face the patient seated on the
Same side of a small table
Opposite side of a small table
Parallel side of a small table
Perpendicular side of a small table
12. Which type of frames must almost always be heated to be aligned?
Plastic
Metal
Both and
None of the above
13. To check for which type of the following a ruler or straight edge is placed so that its edge goes across the inside of the entire front of the spectacles below the nosepad area?
Vertical alignment
Four point touch
Both and
None of the above
14. Which file is used for reslotting screws or making a slot where none previously existed?
Slotting
Pillar
Zyl
Rat-tail
15. Pressure on the nose bridge can cause
Sores
Pain
Rodent ulcers
All of the above
16. No patient should ever be allowed to take away finished spectacles until they have been
Rejected and adjusted
Fitted and adjusted
Both and
None of the above
17. All communication between a are a form of 'marketing'.
Practitioner
Patient
Both and
None of the above
18. Slotting of which of the following is used for reslotting screws or making a slot?
Ruler
File
Pin
None of the above
19. Plastic frames and metal frames can be
Fine tuned to fit the patient
Tight tuned to fit the patient
Both and
None of the above
20. The order of procedure for aligning metal frames is the same as that used for plastic frames, starting with the
Bridge
Temple
Lenses
None of the above
21. Patient's first view of his new glasses should be of a poorly adjusted frame.
True
False
None of the above
Can't say
22. A professional practice is very much a business.
True
False
None of the above
Can't say
23. A skewed bridge will cause one lens to appear lower than the other.
True
False
None of the above
Can't say
24. Too little face form is the case if neither temporal eyewire but only the nasal eyewires touch.
True
False
None of the above
Can't say
25. Proper adjustment temple fold permits the spectacle to easily fit into a standard glasses case.
Angle
Side
Both and
None of the above
26. The things which we should remember
Have a detailed and well-considered financial plan in place
Track income and expenses daily
Know where each cent/peso/franc/fen/paisa, etc. is coming from, and where it is going to
All of the above
27. If the frame is ordered with a given temple width and it comes back with the sides not sufficiently opened, this should be done in the fitting room and not regarded as
An error
A fault
Both and
None of the above
28. When pressing the lenses in opposite directions, it is important that their frontal planes be kept parallel so that which of the following of the frame is not inadvertently introduced?
X-ing
Y-ing
Z-ing
A-ing
29. Whenever the temples do not appear parallel, the frame should first be examined for before the other methods of balancing are tried.
X-ing
Y-ing
Z-ing
A-ing
30. If the temples spread too file the temple where it abuts with front.
Little
Much
Both and
None of the above
Bridge
Temple
Nosepads
None of the above
2. Zyl frames must be
Heated
Melted
Freezed
None of the above
3. The frame front is somewhat twisted so that the planes of the two lenses are out of coincidence with each other, known as
Two Point Touch
Four Point Touch
X-ing
None of the above
4. Which of the following is finer than the Zyl file, and this file is often used to file metal parts of a frame?
Zyl file
Slotting file
Pillar file
Rat-tail file
5. Splay angle should be in the range of
20° to 30°
15° to 30°
25° to 30°
20° to 23°
6. For frontal angle, the tops of the pads should be closer together than the bottoms, angling in towards each other approximately
10°
20°
30°
40°
7. Frames with a heavy front and light sides will tend to slip
Forwards
Backwards
Downwards
Upwards
8. What do patients/customers want?
Reliability and Responsiveness
Assurance and Empathy
Tangibles
All of the above
9. Which parameter to bend of hockey end sides can be adjusted within a few millimetres and in fact, is best done with the patient's presence?
Height
Length
Width
Depth
10. Which of the following progressive lens designs will provide wider fields of clear vision, at the expense of higher levels of swim, distortion and blur?
Harder
Softer
Both and
None of the above
11. The most convenient method of dispensing and adjusting the finished glasses is for the practitioner to face the patient seated on the
Same side of a small table
Opposite side of a small table
Parallel side of a small table
Perpendicular side of a small table
12. Which type of frames must almost always be heated to be aligned?
Plastic
Metal
Both and
None of the above
13. To check for which type of the following a ruler or straight edge is placed so that its edge goes across the inside of the entire front of the spectacles below the nosepad area?
Vertical alignment
Four point touch
Both and
None of the above
14. Which file is used for reslotting screws or making a slot where none previously existed?
Slotting
Pillar
Zyl
Rat-tail
15. Pressure on the nose bridge can cause
Sores
Pain
Rodent ulcers
All of the above
16. No patient should ever be allowed to take away finished spectacles until they have been
Rejected and adjusted
Fitted and adjusted
Both and
None of the above
17. All communication between a are a form of 'marketing'.
Practitioner
Patient
Both and
None of the above
18. Slotting of which of the following is used for reslotting screws or making a slot?
Ruler
File
Pin
None of the above
19. Plastic frames and metal frames can be
Fine tuned to fit the patient
Tight tuned to fit the patient
Both and
None of the above
20. The order of procedure for aligning metal frames is the same as that used for plastic frames, starting with the
Bridge
Temple
Lenses
None of the above
21. Patient's first view of his new glasses should be of a poorly adjusted frame.
True
False
None of the above
Can't say
22. A professional practice is very much a business.
True
False
None of the above
Can't say
23. A skewed bridge will cause one lens to appear lower than the other.
True
False
None of the above
Can't say
24. Too little face form is the case if neither temporal eyewire but only the nasal eyewires touch.
True
False
None of the above
Can't say
25. Proper adjustment temple fold permits the spectacle to easily fit into a standard glasses case.
Angle
Side
Both and
None of the above
26. The things which we should remember
Have a detailed and well-considered financial plan in place
Track income and expenses daily
Know where each cent/peso/franc/fen/paisa, etc. is coming from, and where it is going to
All of the above
27. If the frame is ordered with a given temple width and it comes back with the sides not sufficiently opened, this should be done in the fitting room and not regarded as
An error
A fault
Both and
None of the above
28. When pressing the lenses in opposite directions, it is important that their frontal planes be kept parallel so that which of the following of the frame is not inadvertently introduced?
X-ing
Y-ing
Z-ing
A-ing
29. Whenever the temples do not appear parallel, the frame should first be examined for before the other methods of balancing are tried.
X-ing
Y-ing
Z-ing
A-ing
30. If the temples spread too file the temple where it abuts with front.
Little
Much
Both and
None of the above
Other Question Papers
Departments
- Centre for Corporate Education, Training & Consultancy (CCETC)
- Centre for Corporate Education, Training & Consultancy (CCETC)
- National Centre for Disability Studies (NCDS)
- School of Agriculture (SOA)
- School of Computer and Information Sciences (SOCIS)
- School of Continuing Education (SOCE)
- School of Education (SOE)
- School of Engineering & Technology (SOET)
- School of Extension and Development Studies (SOEDS)
- School of Foreign Languages (SOFL)
- School of Gender Development Studies(SOGDS)
- School of Health Science (SOHS)
- School of Humanities (SOH)
- School of Interdisciplinary and Trans-Disciplinary Studies (SOITDS)
- School of Journalism and New Media Studies (SOJNMS)
- School of Law (SOL)
- School of Management Studies (SOMS)
- School of Performing Arts and Visual Arts (SOPVA)
- School of Performing Arts and Visual Arts(SOPVA)
- School of Sciences (SOS)
- School of Social Sciences (SOSS)
- School of Social Work (SOSW)
- School of Tourism & Hospitality Service Sectoral SOMS (SOTHSM)
- School of Tourism &Hospitality Service Sectoral SOMS (SOTHSSM)
- School of Translation Studies and Training (SOTST)
- School of Vocational Education and Training (SOVET)
- Staff Training & Research in Distance Education (STRIDE)
Subjects
- Basic Of Refractive Errors
- Basic Science
- Coating
- Frames
- Ophthalmic Optics
- Optical Counter Management
- Progressive Lens