Exam Details
| Subject | Mechatronics | |
| Paper | ||
| Exam / Course | Diploma -VIEP-Electrical Engineering (DELVI)/Advanced Level Certificate Course In Electrical Engineering (ACELVI) | |
| Department | School of Engineering & Technology (SOET) | |
| Organization | indira gandhi national open university | |
| Position | ||
| Exam Date | December, 2016 | |
| City, State | new delhi, |
Question Paper
No. of Printed Pages: 3 IBIEEE-004!
B.Tech. -VIEP -ELECTRICAL ENGINEERING (BTELVI) Term-End Examination December, 2016 -iU-i4 ..:5
BIEEE-004 MECHATRONICS
Time hours Maximum Marks: 70
Note: Attempt an,y seven questions. All questions carry equal marks. Use of scientific calculator is Permitted.
1. Describe the components of a continuous sensing system with a neat block diagram.
What are the main advantages of a capacitive proximity switch. over the inductive proximity switch? 5+5
2. What are the two types of data transfer techniques used in computer interfacing List out the main differences between them.
Describe and compare the characteristics of proportional integral derivative control system. 5+5
3. Explain the principle of operation of an Ultrasonic Range Sensor with the help of a neat diagram.
Explain the working of any transducer. 5+5
4. Discuss the measure features of mechatronics systems with the help of a typical example.
Write down the important guidelines for the selection of a sensor. 5+5
5. Explain the process control system with the help of a block diagram.
Why is feedback used in a process control system Describe the difference between open-loop and closed-loop control systems. 5+5
6. With a neat explain Programmable Logic Controller (PLC).
A differential amplifier is to have a voltage gain of 100. What will be the feedback resistance, if the input resistances are both 1 k ohm? 5+5
7. Describe various types of cams.
Write about the mechatronics approach in a microprocessor controlled washing machine. 5+5
8. An integral controller has a set point of 50% and a value of K1 of 0.10/sec. The error starts at zero and changes at per second for 2 seconds before becoming constant for 3 seconds. What will be the output after times of
1 second, and
3 seconds?
9. Write short notes on any two of the following: 2x5=10
Industrial Robot
Computer Printer
Timer
Automatic Engine Control
B.Tech. -VIEP -ELECTRICAL ENGINEERING (BTELVI) Term-End Examination December, 2016 -iU-i4 ..:5
BIEEE-004 MECHATRONICS
Time hours Maximum Marks: 70
Note: Attempt an,y seven questions. All questions carry equal marks. Use of scientific calculator is Permitted.
1. Describe the components of a continuous sensing system with a neat block diagram.
What are the main advantages of a capacitive proximity switch. over the inductive proximity switch? 5+5
2. What are the two types of data transfer techniques used in computer interfacing List out the main differences between them.
Describe and compare the characteristics of proportional integral derivative control system. 5+5
3. Explain the principle of operation of an Ultrasonic Range Sensor with the help of a neat diagram.
Explain the working of any transducer. 5+5
4. Discuss the measure features of mechatronics systems with the help of a typical example.
Write down the important guidelines for the selection of a sensor. 5+5
5. Explain the process control system with the help of a block diagram.
Why is feedback used in a process control system Describe the difference between open-loop and closed-loop control systems. 5+5
6. With a neat explain Programmable Logic Controller (PLC).
A differential amplifier is to have a voltage gain of 100. What will be the feedback resistance, if the input resistances are both 1 k ohm? 5+5
7. Describe various types of cams.
Write about the mechatronics approach in a microprocessor controlled washing machine. 5+5
8. An integral controller has a set point of 50% and a value of K1 of 0.10/sec. The error starts at zero and changes at per second for 2 seconds before becoming constant for 3 seconds. What will be the output after times of
1 second, and
3 seconds?
9. Write short notes on any two of the following: 2x5=10
Industrial Robot
Computer Printer
Timer
Automatic Engine Control
Other Question Papers
Departments
- Centre for Corporate Education, Training & Consultancy (CCETC)
- Centre for Corporate Education, Training & Consultancy (CCETC)
- National Centre for Disability Studies (NCDS)
- School of Agriculture (SOA)
- School of Computer and Information Sciences (SOCIS)
- School of Continuing Education (SOCE)
- School of Education (SOE)
- School of Engineering & Technology (SOET)
- School of Extension and Development Studies (SOEDS)
- School of Foreign Languages (SOFL)
- School of Gender Development Studies(SOGDS)
- School of Health Science (SOHS)
- School of Humanities (SOH)
- School of Interdisciplinary and Trans-Disciplinary Studies (SOITDS)
- School of Journalism and New Media Studies (SOJNMS)
- School of Law (SOL)
- School of Management Studies (SOMS)
- School of Performing Arts and Visual Arts (SOPVA)
- School of Performing Arts and Visual Arts(SOPVA)
- School of Sciences (SOS)
- School of Social Sciences (SOSS)
- School of Social Work (SOSW)
- School of Tourism & Hospitality Service Sectoral SOMS (SOTHSM)
- School of Tourism &Hospitality Service Sectoral SOMS (SOTHSSM)
- School of Translation Studies and Training (SOTST)
- School of Vocational Education and Training (SOVET)
- Staff Training & Research in Distance Education (STRIDE)
Subjects
- Basics of Electrical Engineering
- C - Programming
- Computer Applications In P.S.
- Control Systems
- Digital Control System
- Digital Control System Design
- Dynamics System Simulation
- Electrical Circuit Theory
- Electrical Engineering Material
- Electrical Installation and System
- E l e c t r i c a l M a c h i n e T h e o r y I I
- Electrical Machines-I
- Electrical Measurements And Instruments
- Electrical Power Transmission and Distribution
- Energy Audit
- Flexible Ac Transmission System
- Industrial Drives and Controls
- Mechatronics
- Power Generation System
- Power Plant Economics And Centering
- Power System Reliability
- Principles of Computer Architecture
- Special Electrical Machines
- Switchgear And Protection
- Utilization Of Electrical Engineering